尼铁现代化项目中矩形空心桥台的优化设计

当前常用的时速200 km的铁路矩形空心桥台参考图中的桥台截面尺寸偏厚,安全富余量很大。为节约混凝土圬工量,希望在保证安全的前提下减少桥台截面尺寸。首先提出专门针对铁路矩形空心桥台台身截面计算的荷载图示,然后利用这一新的图示对拉伊铁路项目中使用的常规矩形空心桥台进行有限元分析,经过不断试算提出最优的截面尺寸。在钢筋用量基本不变的情况下,新尺寸桥台较原参考图中桥台的混凝土用量减少10%以上。对于项目所在地尼日利亚国水泥价格高昂的情况而言,桥台尺寸的这一优化将产生较大的经济效益。     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

STX1(2)型驮背多功能运输车超偏载检测标准

分析了STX₁₍₂)型驮背多功能运输车对既有超偏载检测方法和标准的适应性,提出了该车的超偏载检测方案,明确了公路货车或半挂车超偏载的检测方法及评判标准。     

超大型自航抓斗挖泥船作业流程载荷分析

以大型自航抓斗挖泥船为研究对象,建立相应的水动力计算模型。主要研究抓斗挖泥作业不同阶段下船舶运动、锚泊线受力情况以及其随不同环境载荷的变化规律,为船舶安全作业提供依据。研究结果表明,船舶在抓斗旋转和卸料时最为危险,船舶横荡、横摇及各锚泊线张力受其影响很大,实际作业时应尽量保持迎浪状态,进而确保船舶作业安全。     

压载荷下骨材贯穿孔孔边应力集中模型试验

以船舶双层底结构为研究对象开展模型试验,研究板材中的开孔在承受压力载荷作用下的孔边应力分布情况,分析压力载荷下不同开孔孔型以及不同补强结构对孔边应力分布情况的影响。在此基础上,开展相关仿真分析,将试验结果与有限元仿真结果进行对比,验证有限元仿真的准确性。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

An improved cellular automaton with axis information for microscopic traffic simulation

Cellular Automaton (CA), an efficient dynamic modeling method that is widely used in traffic engineering, is newly introduced for traffic load modeling. This modeling method significantly addresses the modest traffic loads for long-span bridges. It does, however, require improvement to calculate precise load effects. This paper proposed an improved cellular automaton with axis information, defined as the Multi-axle Single-cell Cellular Automaton (MSCA), for the precise micro-simulation of random traffic loads on bridges. Four main ingredients of lattice, cells’ states, neighborhoods and transition rules are redefined in MSCA to generate microscopic vehicle sequences with detailed vehicle axle positions, user-defined cell sizes and time steps. The simulation methodology of MSCA is then proposed. Finally, MSCA is carefully calibrated and validated using site-specific WIM data. The results indicate: (1) the relative errors (REs) for the traffic parameters, such as volumes, speeds, weights, and headways, from MSCA are basically no more than ±10% of those of WIM data; (2) the load effects of three typical influence lines (ILs) with varied lengths of 50, 200 and 1000 m are also confidently comparable, both of which validate the rationality and precision of MSCA. Furthermore, the accurate vehicle parameters and gaps generated from MSCA can be applied not only for precise traffic loading on infrastructures but also for the accurate estimation of vehicle dynamics and safety. Hence, wide application of MSCA can potentially be expected.     

大型C型独立液货罐Y型接头疲劳强度评估

随着C型独立液货罐的新技术发展,目前在工业界推出了采用双体罐和三体罐构造形式的新颖大型C型独立液货罐。由于双体罐和三体罐构造的要求,在相邻罐体连接处设有Y型接头。该Y型接头位置处由于结构件交汇,构造复杂、应力集中,在船舶运动、蒸汽压力变化,以及温度变化的动载作用下有可能发生疲劳损伤。本文对新颖大型C型独立液货罐Y型接头疲劳强度评估方法的规范技术要求及制定开展了深入详尽的研究，包括对C型独立液货罐疲劳损伤计算工况择取，液货内部动压力计算公式推导，蒸气压力、温度变化等低周疲劳载荷模式确定等，创新提出一整套基于热点应力的C型独立液货罐Y型接头的疲劳损伤评估方法的规范实施要求。进一步地，还推导了基于一般实际情况假设下的C型独立液货罐Y型接头疲劳评估筛分准则，并应用本文上述研究成果和结论，进行了双体和三体罐Y型接头疲劳评估和筛分准则的应用与验证。     

动态载荷识别的自适应延迟逆模型方法

为减小载荷识别问题对原系统先验知识的依赖,采用系统的自适应延迟逆模型识别时域载荷。采用自适应算法辨识延迟逆模型,代替了一般识别方法中的系统特性矩阵求逆过程,避免了病态问题。随后将工作状态下的响应作为逆模型的输入,则其输出就是时域载荷的延迟估计。通过对两端简支梁结构进行载荷识别的仿真研究,以及对双层隔振试验台架的试验研究,识别了稳态激励和瞬态激励,验证了该方法的有效性。该方法不需要了解系统的数学模型及参数,因此能够应用于工程实践中。